How To Remove Paint From Wood Gun Stock

Coat the stock and wrap it in foil so it doesnt dry too quickly. Straight up not diluted.

Pin On Houtbranden

Prevents a lot of problems with finish drying.

How to remove paint from wood gun stock. A heat gun is a terrific tool to get paint off wood furniture or to remove adhesive residue from wood. Try whatever you use on a hidden area under the handguards. Using a heat gun will help you if the painted wood surface has a lot of paint layers and you want to get to the bare wood.

To see if it is attacking the coating on the rifle. Check the best sander for removing paint I recommend. Then take a cheapie towel wrap it around the stock cover that bit in a trash bag.

Scrub the entire project with nylon brushes or abrasive pads to remove all traces of the old finish and the stripper sludge. Acetone is a strong solvent I would try xylene xylol before acetone. Applying soulble Iron compounds to wood with a high Tannin content is an old method of staining wood Walnt used in gun stocks has a high Tannin content.

More complicated refinishing issues need to be discussed before we both commit to your gunstock restoration. Wrap it in saran wrap and set it in the sun for an hour or two. You can dissolved Steel Wool in Vinegar or any acid of your choice to make soluable Iron compounds.

Sealing the wood of a gunstock is one of the most important steps in stock finishing. Use a paint scraper putty knife or specialty scraper to remove the softened paint being careful to not gouge the wood. Id degrease first to eliminate previous oil rubs then bleach to remove old stains.

Apply a thin coating and allow 20 minutes or so for the oil to penetrate then wipe it off and then rub with your bare hands hard enough that your hands feel really warm from the friction which helps to smooth and even out the oil let cure for 12 to 24 hours and. Once youve bleached the wood to the degree of color you want give the stock a coat of sanding sealer then hit it with some fine steel wool. Get Paint off Wood Furniture with a Heat Gun.

Must state on the label that it will remove an epoxy finish to have a chance. If solvents do not work other options include specialty paint removers or even easy off oven cleaner but these may attack the coating on the weapon. Reapply the paint stripper to detailed or problem areas.

If youre happy with the color at this point apply the finish of your choice. Use a course-grit sandpaper to work the lacquer finish off the stock of the gun. Using DIY methods carefully and with extreme caution.

Hopefully this guide will help you make the best paint remover for wood. Dont worry if you get some on the metal because the gun has gone through a process that protects it and a little water wont harm it. In this GunTec presentation Larry Potterfield Founder and CEO of Midw.

Removing a Browning finish is a nightmare. For all those tempted forget about it. Removing paint from a hard surface such as wood is not an easy task but it is possible.

If its cosomoline soaked I first take off all the metal and clean them off with paint thinner. You too can remove accidental paint marks from wood. Judicious sanding to remove old wood stain and create the crucial uniform wood surface.

I then take a cloth thats soaked in the stuff and give a brief scrubbing of the wood. It is similar to a hairdryer but it uses higher temperatures that melt paint from the wood surface making the act of scraping away old paint. Works good on everything but epoxy type finishes they take multiple coats of stripper and a bunch of scraping.

Pour it over the wood and message it into the woodgrain. Using a heat gun to remove paint from wood. Acetone wont even remove Tru-oil and it bounces off a Browning finish.

You can darken the affect by first soaking the wood with Tannic Acid. This takes some patience but is required in order to properly paint the stock. If I might add a hint- after stripping wash off the stock with paint thinner even if the stripper is a no wash type then let the stock dry for at least a day before sanding and finishing.

Most strippers will not remove a Browning finish. You can use a heat gun or sander to remove paint. Once the surface is sanded wash the stock in hot water.

Gouges deep scratches chips out of the wood and cracked wood are more complicated issues that need to be handled separately. Although I must say its quite labor-intensive itll speed up the.

Refinishing A Gun Stock 7 Steps Instructables